Wpa2 psk dictionary file

Use the command ifconfig [interface name] down to bring an interface down. In this case as the name of our interface is wlan0, the command to execute would be:. Once the interface is down, you need to change the MAC address of your device using macchanger. This MAC address is known as it's always spoofed. After the execution of the command, the previous MAC address and the new one will be printed as reference:. Monitor mode is one of the seven modes that The monitor mode sniffes the packets in the air without connecting associating with any access point.

As this mode doesn't need association to AP needed and no authentication. In case you get an exception, a warning or a message that some processes could cause troubles during the execution of this process, be sure to stop the processes using the following command:. From the "table" generated by the previous command, you now need to copy the name of the interface in monitor mode, in this case the name is wlan0mon. This name will be used by the rest of the commands that need access to the interface.

We need to copy the WPA Handshake of the Wi-Fi router to hack it as a dictionary attack that waits till the signal goes to the router, then comes back, fails and repeats the process again and again is very unproductive A handshake is basically an automatic process of negotiation between two entities, usually your computer and the network server it wants to connect to.

It's the procedure that sets the configurations and parameters needed to make the communication channel run smoothly without manually putting in specifications and whatnot every time you connect heterogeneous systems or machines together. As first, you need to dump all the Wi-Fi signals available in the environment. To do it we are going to use airodump-ng that expects as first parameter the name of the interface in monitor mode. Execute the following command to dump the Wi-Fi networks:.

From this table you should copy the information the row about the network that you want to hack on in the notepad as you will need this information later channel-CH and BSSID. Will copy the WPA Handshake of the modem that you want providing the required parameters. The channel and BSSID arguments can be retrieved from the previously obtained using airodump-ng wlan0mon. The w argument needs to be the path of the folder in which you want to save the Handshake of the modem, lastly the name of the interface in the monitor mode wlan0mon.

So, our command to execute would look like:. This process could take several minutes, in our case it took just 4 minutes, however this may vary in every network and devices:.

To speed the process of obtain the WPA Hanshake, you can use a mobile device or other computer that is connected to the Wi-Fi network. Just turn off the Wi-Fi in your device and turn it on again, this should speed the process. CoNdOmZrUz says:. Thursday,December 8, at Saturday,December 17, at Dme says:. Sunday,December 25, at Tuesday,December 27, at Friday,January 6, at Wednesday,January 11, at Friday,January 13, at Sunday,February 12, at Ahmed Hakeem says:.

Tuesday,February 21, at Saturday,March 3, at Sunday,March 18, at Thursday,March 29, at Spanish Dictionary Wpa Taringa! Monday,April 30, at Saturday,September 1, at Thursday,September 6, at Tuesday,October 16, at Monday,November 5, at Anonyme says:. Monday,April 29, at Karim Mostafa says:. Thursday,May 9, at Sunday,May 26, at Wednesday,May 29, at Friday,May 16, at Friday,December 19, at Saturday,May 23, at Pinoy Anonymous says:. Monday,August 24, at Tuesday,March 1, at Jeremy Drahos says:.

Thursday,March 3, at Stud says:. Wednesday,December 7, at The operating system recognizes a wireless interface named wlan0.

Step 3: My next step will be to enable the wireless interface. This is accomplished issuing the ifconfig wlan0 up command. Step 4: I need to understand what wireless networks my wireless card sees. I issue the iwlist wlan0 scanning command. This command forces the wireless card to scan and report on all wireless networks in the vicinity. You can see from this example it found my target network: Wireless Lab.

Secondly, we see the AP is transmitting on channel This is important because it allows us to be specific on what wireless channel we will want our wireless card to monitor and capture traffic from.

The next step is to change the wireless card to monitoring mode. This will allow the wireless card to examine all the packets in the air. We do this by creating a monitor interface using airmon-ng. Issue the airmon-ng command to verify airmon-ng sees your wireless card. From that point create the monitor interface by issuing the command: airmon-ng start wlan0.

Next, run the ifconfig command to verify the monitor interface is created. We can see mon0 is created. Now verify the interface mon0 has been created. Step 6: Use airodump-ng to capture the WPA2 handshake.

The attacker will have to catch someone in the act of authenticating to get a valid capture.